This is the second in a three part review on LEDVANCE lighting and home automation products. The first review was for LEDVANCE’s Sylvania Lightify A19 LED bulb review. This review focuses on the LEDVANCE LED Flexible Strip RGBW. It is a 16-foot flexible strip that can be laid out to fit a variety of locations. The strips can be set to any color and can also tune white, changing from a correlated color temperature (CCT) of a warm 1900K all the way up to a daylight simulating 6500K. While people have been decorating their houses with white LED string lights for years, this product has some unique advantages if you control it with an IFTTT/Stringify integrated hub. Read on to see what I think…
Parts of the system
The light strip is powered by a 12 VDC transformer and controlled by a logic circuit. Both these parts are external to the light strip so the complete unit is made of 3 distinct parts: the transformer, the control module, and the light strip.
The transformer is a rather large unit at 4 3/16″ long, 2″ wide and 1 5/16″ deep (not including the ungrounded prongs). It has a circular threaded 2 contact connector on the bottom to which the cable to the lamp connects.
Because of the length of the connection and strain relief on the cable, after connecting the transformer, about 5 1/2″ will be positioned straight down from the top of the transformer. this may be a challenge for most weatherproof enclosures. While the cord does not need to be installed within the enclosure you may find that it prevents plastic shrouds and weatherproof doors from fully closing. The transformer output is rated for 12 VDC and 2 amps, which equals 24 watts, but even though the packaging and product code indicate 24 watts, the warning label attached to the light strip says that the lamp draws 29 watts.
There is about 2 feet of power cord between the transformer and the control module for the light strip. The control module is 2″ long, 1 3/8″ wide and 7/8″ high black plastic box that is DC powered and outputs the correct voltage and current for the red, green, blue, and white LEDs in the light strip. I suppose that the ZigBee radio is in this box too, so it should be mounted where it will be free to communicate with the ZigBee hub.
The light strip connects to the control module with 10″ of cable. The light strip is comprised of 16′ of rectangular silicone that contains a flexible copper strip with resistors and surface mounted LEDs. Due to the wiring connections and the extra length of the ribbon on each end, the overall length of the light strip is 16′ 1 1/2″ and it measures 9/16″ wide by 3/16″ deep. The electronics of the unit are composed of eight 2′ sections. Each section contains 12 resistors and 24 LEDs: 12 RGB LEDs and 12 white LEDs. The LEDs are arranged with a RGB LED adjacent to a white LED and each grouping is spaced 2″ apart. All the LEDs are mounted on one side of the strip, which also acts as a heat sink for the components. The picture above shows the light strip bent back on itself and includes details of how the LEDs are grouped together, the resistors, and the soldering of 2 of the 2′ sections (the solder from the tip of the section on the top left connects and contacts the section adjacent to the letters on the top right.)
Installation
The kit comes with 16 plastic brackets and 34 wood screws to mount the light strip and control box to most surfaces. The installation instructions recommend not using staples or other fasteners that can potentially puncture the outside of the strip or damage the components inside. Because of the flexibility of the fasteners and the average installation offset of 1 foot, it is difficult to get a good tight fit in corners, even though the strip will bend as tightly as ½”. Also, because of the flat strip inside, the layout of the light strip should ideally follow a two-dimensional path as much as possible. It is possible to make left and right turns of the strip if you make a brief excursion into 3D, like so:
Also, while cutting the strip will leave the non-powered end useless, and at the same time expose the internals to the environment, it should be possible and permissible if the strip will be used indoors. In this case, the strip should be cut at one of the 7 internal junctions. A junction is shown in the picture above at the lower left. However, the packaging insert indicates that the strip should not be cut to length. This is especially true of outdoor installations. So, if you are planning to use this outside, the 16’ design will have to be a hard constraint.
Operation
The LEDVANCE LED Flexible Strip RGBW is designed to be operated through the ZigBee network. It is optimally plugged into a receptacle that is always powered. Most ZigBee hubs will recognize this as a RGBW light and will allow turning the light on and off, changing the color of the light, and tuning the correlated color temperature. The Lightify hub will also allow you to set the default on and off dim rate so that the turning on and off of the light is not abrupt.
Based upon the desired color temperature, level, saturation, and hue the controller will illuminate the RGB and/or white LED to a particular setting. The picture below illustrates all four LEDs illuminated at a low setting and photographed at 1/800 sec, F8 using an ISO1600 setting.
Note that all of the LEDs are controlled on the same circuit. Therefore, this light cannot perform chase or multi-color displays. The benefit of this product is that it can turn on and off and change color, color temperature, hue, level and saturation based on external criteria through IFTTT, Stringy, SmartThings, or other ZigBee enabled hub. Note that the Lightify hub does not have connectivity to IFTTT or Stringify, so using this hub will only allow you to control the lights through the app on a phone and also using Amazon Alexa. Also, although this can be programmed to change color, hue, level and saturation at fixed intervals, because of the latency in the ZigBee signals, it is unlikely that this can be synced to music or video.
Performance
One of the things that I thought was important for this light strip was for to match the other LEDVANCE Light bulb that I have in color temperature, intensity and color hue across a range of settings. That way the two products can be used to color a room consistently. In order to achieve these comparisons, I bound both bulb and light strip to my SmartThings hub and I created a program to set the various settings to the same value for both devices. As far as the color temperature correlation between the two devices. I placed the bulb in a desk lamp fixture and lay the strip, coiled on a white painted bench in our mud room. I focused my comparison on the color and intensity reflected off of the rear of the bench.
As indicated above, color temperature performance seemed to be a little off between the bulb and the strip. However the disparity I observed first-hand does not seem as bad as what is shown above. The 2700K color seems a little bit too green and the higher temperature colors seem too blue. As discussed below, the strip has some issues displaying green when it should be displaying yellow. I have a feeling this may be due to the silicone casing.
The brightness level also seemed a little bit different from the A19 bulb, but this should be expected since the bulb has a translucent cover and the strip has the bare LEDs exposed. Also the illuminance per sq. ft. may be the same but because the strip is larger it appears brighter. In the end, they both dim down to what must be only a few candelas.
The color performance of the strip seemed to be very close to the bulb, with the exception of yellow. The yellow from the bulb seemed to be a little bit green hued. You can see a little green in the corner of the picture that is mostly yellow. The light was washing out the picture so I needed to adjust my shot to avoid the lamp completely.
Conclusion
The LEDVANCE LED Flexible Strip RGBW is a unique product to allow programmatic or automatic control of weather proof light strips. While other light strips are available that are weatherproof, allow chase, and/or sync to music, they do not allow automation. Other light strips are available that permit automation but they are not weatherproof. The light strip retail price is roughly four times higher than a waterproof color-changing and color-selectable strip with IR remote. But if you want to ask Alexa to on/off and adjust the colors of the light strip around your hot tub (probably the killer app for this item) then the LEDVANCE LED Flexible Strip is the way to go!
Source: The sample for this review was provided by LEDVANCE Sylvania. Please visit their site for more info and Amazon to order.
Product Information
| Price: | $99.99 |
| Manufacturer: | LEDVANCE Sylvania |
| Retailer: | Amazon |
| Requirements: |
|
| Pros: |
|
| Cons: |
|
Filed in categories: Home and Kitchen, Reviews
Tagged: LED lighting
Sylvania LEDVANCE LED Flexible Strip RGBW review originally appeared on on March 18, 2017 at 8:57 am.
Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://ift.tt/1nJlrA1 in order to ensure continuous delivery.
Sylvania LEDVANCE LED Flexible Strip RGBW review
Aucun commentaire:
Enregistrer un commentaire